How to Use Hamilton Beach Flexbrew – Single Serve and Carafe

If you are a coffee lover, you should know how to get a perfect cup of coffee using a Hamilton Beach Flexbrew coffee maker. Well, there’s no need to worry! Read this quick post and learn how to use your Hamilton Beach Flexbrew Coffee Maker.

It lets you brew two types of coffee at once, and you can also program it to brew just the right amount of coffee for you. So, Continue reading to learn how to make coffee with this coffee maker.

How to Brew a Single-serve Pack

Step 1. Plug into the power source. Press the single-serve button.

Step 2. Lift the top hook until the top fits properly.

Step 3. Embed the channel in the opening. Place a dark removable single-serve pack holder in the channel, adjusting the handle to the pipe handle.

Step 4. Insert a pack into the single-serve holder. Try not to eliminate the foil.

Step 5. Close the cover and snap it set up to puncture the single-serve pack.

Step 6. Lift the single-serve water repository cover.

Step 7. Fill a cup or travel cup into which the espresso will be fermented and add water to the water supply. 10 oz. (296 ml) of water is the Maximum sum for single-serve packs.

Step 8. Close the cover. Press the BREW STRENGTH button to choose normal or strong.

Step 9. Utilize the cup rest for a cup or mug and eliminate the cup rest for a movement mug.

Step 10. Press the Mix NOW I/button to begin blending. The mix marker light will illuminate to show that the espresso producer is fermenting. The espresso producer will shut down naturally while preparation is finished.

Step 11. Press the Brew NOW I/O button to switch it off. Turn off.

Step 12. Channel and single-serve pack holders ought to be washed after each utilization.

How to Brew Single-serve Ground Coffee

Step 1. Plug into the power source.

Step 2. Lift the cover lock until the top fits properly.

Step 3. Embed the funnel in the opening. Open the mix container top; then put the brown removable blend bin on the ledge.

Step 4. Add ground espresso to a brown removable blend bin (3 tablespoons [44 ml]) most extreme.

Step 5. Close the mix container top. Place the mixing container in the funnel, adjusting the handle to the funnel handle.

Step 6. Close the top and snap it set up to hook the cover shut.

Step 7. Lift the water reservoir top.

Step 8. Fill a cup or travel cup (14 oz/414 ml MAX) into which the espresso will be blended and add water to the water reservoir.

Step 9. Close the water reservoir top.

Step 10. Utilize the cup rest for a cup/mug OR eliminate the cup rest for a movement mug.

Step 11. Press the Blend NOW I/O button to begin preparing. The brew pointer light will illuminate to show that the espresso creator is fermenting. The espresso producer will shut down consequently while preparation is complete.

Step 12. Press the Blend NOW I/O button to switch it off. Unplug.

Step 13. The funnel and mix bin ought to be washed after each utilization.

How to Brew a Carafe

Step 1. Plug into the power source.

Step 2. Press the carafe button.

Step 3. Lift the cover. Eliminate the carafe blend bin.

Step 4. Place a paper espresso channel in the carafe brew crate. For some espresso being made, place one level tablespoon (15 ml) of grounds into a paper channel.

Step 5. Place the carafe blend bin once more into the carafe brew bushel holder.

Step 6. Fill the carafe with up to 12 cups of cold water and empty it into the carafe water supply.

Step 7. Close the cover.

Step 8. Place the carafe, with the carafe cover connected, on the warming plate.

Step 9. Press the Brew STRENGTH button to change solidarity to Striking.

Step 10. Press the Blend NOW I/button to begin fermenting. The brew pointer light will illuminate to show that the espresso creator is on.

Step 11. Press the Blend NOW I/button to switch it off. Turn off.

Step 12. The carafe mix bin holder and carafe ought to be flushed after each utilization.

The Programming Is Only for the Carafe Side

Only one side of the unit can be brewed at a time. When the carafe side is programmed, the single-serve side cannot be used.

1. The coffee maker cannot be programmed until the time is set. Press and pulse the SET TIME button to set the correct time in AM or PM. Wait for three seconds. Take a few minutes to pulse or hold.

2. The PROG button is used to program. Begin Time is noticeable on the presentation and blazes at 19:99 by default.

Press the SET TIME button to set the ideal preparation time in AM or PM while holding the PROG button. PM. Stand by 3 seconds; minutes will streak. Pulse to set minutes. Discharge the PROG button. Press and delivery the PROG button again to initiate the programmed blend. The PROG light will enlighten.

TIP: To check the beginning time, press and hold the PROG button. The time you set will be shown and can be changed by repeating the steps above. Press the PROG button to reactivate the programmed blend and the light will enlighten.

Notes:

• Utilize just cold water in supply. Try not to utilize boiling water.

• Try not to warm espresso in the machine.

• Try not to utilize creamer or nondairy flavor in supply.

• Assuming the brew pointer light blazes multiple times, the top isn’t shut. Lower the top until it snaps to lock. Press BREW NOW I/O button.

• Try not to mix espresso without the removable needle holder getting into place.

• Try not to brew espresso without a brown removable brew bin and channel set up.

• If you have silt from the espresso, add a #1 paper cone espresso channel to the brown removable blend bin.

How to Clean Your Coffee Maker

All espresso creators ought to be cleaned no less than one time each month.

Step 1: Plug into the power source.

Step 2: Pour 3/4 cup (177 mL) of plain white vinegar and 3/4 cup (177 mL) of cold water into the Supply.

Step 3: Place a 14-oz. (414-mL) or bigger cup or travel mug under to get the water/vinegar arrangement. Press the BOLD or REG Button once. Following 30 seconds, press the Intense or REG Button again to quit fermenting and permit the vinegar to clean.

Following 30 minutes, press the Intense or REG Button and permit it to complete the brew cycle. At the point when the brew cycle is done, void the cup and flush. Run 2 to 3 patterns of cold regular water. The espresso Producer is cleaned and prepared to blend espresso.

Frequently Asked Questions: